|
|
| |
Operating
Instruction |
| |
| Installation
|
1.The cement surface of earth wants the desiccation, neat.
2.The brush is last a waterproof paste in lay,on all sides brattishing foot beard brush high 20 cm.
3.Taking the keel brush apply oil with 14% of aqua rate below paints,using after needing the shank plumping screw affix the cement surface of earth is last, the wood keel needs the small port in turn on in the center,make keel backward flow ventilated ,or use the high wood in packing sheet in tectonic plate keel may also,(incapability water use silt stemming) then besprinkle top mothballs.
4.Use a multiple layer board1.2-1.8 cm, saw first 120 ×60cm a rectangle cake, brush the apply oil paint, needing shank post will its fix to must stay a 1cm gap at joint in the top of wood keel with the screw.
5.Spread on many laminations a the lay defends the paper of tide(namely the cotton of tectorial membrane foaming),connecting the port with each other the 20 cm,then spread the last floor board wood.Spreading the hour of floor board needs to use the wood screw fixedly good.( incapability usage any glue)
6.Building the hour of floor board want to depend on air space humidity and region differences,wanting to is ordered by pine such as the hour of special and damp region in Northeast of China and in East China,installation floor board,( with the board puts with of board to put a the poker of sheet or bale band is allow roughly 0.5 cm,need the felting completes to take out) the in order to prevent affects by damp and cold the bulge mutation pattern in the damp season.In the northeast,north China and the special dry region in some installation ground wants to depend a little bit tight, with the nature joins together for allow, on all sides by the wall the place all stays an 1.5 cm enzyme regulation seam.
7.The felting of floor board after completing, draw the last floor board wax immediately( the attention draws only in gap at joint,the incapability draws on the board surface)
8.Please according to the above the felting of device and maintain, otherwise,appear strain or other questions,a loss for resulting in has nothing to do with our company.
|
|
|
|
|
| Maintenance |
1.
Retention floor board desiccation,
brushing, disallow the water use
gets a drenching the mop drags
along a ground of or use the lye,
soap aqua scrub, the in order
to prevent breakage varnishes
of shining kilowatt hour, damage
lacker membr-ane.If meet ash or
dirty availability shank mops
or use the wet mop that wring
dry wipe. Every month( or two
months) waxinged once.( the waxing
front wipe with dirty vestige
the aqueous vapour clean).
2. If meet warm air or other leaks
in the surface of earth, must
on time wipe clean, the incapability
insolates with the sun directly
or the electric furnace bakes,
in order to prevent desiccation
over quick, floor board shake.
3. The long-term do not live,
slicing to hate to cover with
the cloth of lastics or newspapers,
time area conc-entration diagram
a lengthways the lacker membrane
glues for the meeting hair,losing
the brightness,slicing to hate
the hot water basin,hot rice thing
to put directly at the same time
on the floor board surface,appliance
wooden board or hassock packing
sheet, very hot bad lacker in
order to prevent membrane.
4. The partial the immodesty of
board surface is stained with
dirty vestige should on time clear
away, if have grease spot availability
dish cloth or the washing powder
between mop hot spring aqua or
jots wipe,and also the n-eutral
soap in availability aqua adds
the few scouring works properly
the scrub . If the dirty vestige
is serious , adopt this logarithm
fitting method logt null and void
, high-quality abrasive paper
in availability or steel wool
to wipe lightly . If is soft cloth
that drug , the dirty vestige
between beverage or coloring agent
, must at the dirty vestige did
not seep into the wood quality
superficy before take into the
clear away clear away device adoption
immerse the furniture wax wipe.
If still invalid , must use steel
wool furniture wax wipes . If
the superficy of the floor board
lay was burned by the cigarette
butt , use, the soft cloth that
immersed the furniture wax make
an effort to wipe and can recover
shining. If the ink taints with,
should on time use to immerse
the soft cloth in wax wipe, if
null and void, can wipe with the
steel wool furniture wax again.
5. Beaded paint floor board that
after building , reduce to the
best the sun set plumb bask ,
the in order to prevent beaded
paint was projected light upon
by ultraviolet ray excessive advancing
the season crack and age. Set
on the floor board furniture appliance
rubber or other soft thing packing
sheets rises , the in order to
prevent depicts the floor board
lacker.
6. Put a piece of packing sheet
in the aperture of door .
|
|
|
|
|
|
|
|
